Concentrated water-based cleaner.

DETERGENT 910 cleaner is suitable for industrial use in printing houses. It removes and cleans water-based inks without damaging the material (mesh, screen frame, etc.) and does not leave stains. It can be used as a degreaser on silicone surfaces before printing. It is recommended to dilute with water up to 20%.

Main characteristics:

DETERGENT 910 is a powerful cleaner that can remove any traces of grease or silicone from difficult printing surfaces for screen printing or any other printing process. This is an innovative water-based detergent, completely biodegradable, and extremely effective at cleaning any demanding surface before printing.

DETERGENT 910 is useful for cleaning screen printing meshes used with very demanding water-based inks. DETERGENT 910 resolves and removes dried old water-based ink from all printing devices or parts of printing machines in a few seconds. This product does not chemically affect the photoemulsion or polymers used in screen printing. In the printing process, it is very important to print on thoroughly cleaned surfaces to achieve better results with printed colors. Additionally, it is crucial to have a solution when facing contamination problems with grease or silicones on hard surfaces like glass, metals, stainless steel, or hard plastic. We usually suggest applying some 910 detergent to the surface with a hand spray, cleaning it, and wiping it with a clean cotton cloth. The process can also be repeated several times with a clean cotton cloth. DETERGENT 910, used in the aforementioned manner, dries very quickly and leaves no residues after two or three seconds, so you can print directly on the cleaned surface.

Dilution of concentrated 910 detergent: This detergent has the highest effectiveness when used as is. We suggest using it in its pure concentration for cleaning glass, stainless steel, metals, melamine, and hard plastics. In the case of cleaning and degreasing surfaces made from soft plastics or aluminum, we recommend diluting it with water – 1 part of 910 detergent to 4 or 5 parts of water.

Warning: This product can dissolve some plastics and metals in certain cases, so we suggest conducting some tests before use.

Murakami MS-THICK capillary film is intended for creating excellent stencils for thick-layer printing or special effect printing (puff, layering, etc.).

An excellent substitute for liquid emulsion. This technology enables the highest level of resolution together with stable results and repeatability.

In stock is THICK capillary film with a thickness of 300 mic. in sheets 40×60 cm.

Other thicknesses of MURAKAMI MS-THICK capillary films (range from 100 to 1000 microns) are available upon prior order.

Image: Comparison of a developed screen coated with liquid emulsion (left) and capillary film (right). Noticeable differences in edge sharpness and smooth surface.

The ergonomic aluminum trough is a crucial tool for the proper application of emulsion, allowing for an even, smooth layer of emulsion on the screen printing mesh.

The aluminum trough is extremely lightweight, making application easy and cleaning effortless. It is made of durable aluminum alloy AL6061T6 with plastic guides at the end. The double edge design (thick and thin) allows for a thicker or thinner layer of emulsion to be applied to the printing mesh. The sharp edge is intended for a thinner application on the screen printing mesh, while the rounded edge allows for a thicker layer of emulsion. During use, the trough can easily be placed on a flat surface without tipping over and causing an emulsion spill.

The part of the trough (that is in contact with the mesh during emulsion application) is protected with a rubber cover that can be easily removed before use and reattached after the application is complete.

Extremely light and high-quality aluminum hand squeegee holder, also resistant to high loads.

Light aluminum holders are suitable for manual use or for manual screen printing due to the anatomically shaped edge.

Aluminum holders can be quickly and easily thoroughly cleaned. You can easily replace the squeegee rubber with another hardness of rubber (depending on printing requirements) or replace it because the old rubber is worn out.

The holder already has a medium-hard green rubber (75SH).

It is available in four different lengths: 20, 30, 35, and 40 cm.

Murakami MS capillary film is intended for creating excellent stencils with very simple application techniques.

An excellent replacement for liquid emulsion, with which you will easily develop fine details at the most demanding resolutions.

In stock is a capillary film with a thickness of 80 microns and 100 microns in a roll 0.64 x 10 m, which can be ordered by the meter.

All other thicknesses (from 15 to 100 microns) are available by pre-order.

PHYSICAL PROPERTIES:

› light blue colored capillary film

› thickness from 15 to 100 microns

› for UV, solvent, and textile color systems

› exceptional resolution

› durable in larger runs

› simple application process (with water or emulsion)

CAPILLARY FILM CAN BE APPLIED IN TWO WAYS:

APPLICATION METHOD WITH LIQUID EMULSION:
1. remove the protective film from the capillary film
2. place the film with the bare side up on a flat table
3. lay the screen over the film so that the mesh touches the film
4. pour a little liquid emulsion on the screen on the top side of the film1POT SOL C2 or Screencoat WHDthen pull evenly across the film with the squeegee twice.
5. dry the screen in a warm chamber (up to 40°C) in a horizontal position
6. the prepared screens can wait for several months in a dark place.

METHOD OF APPLICATION WITH WATER:
1. remove the protective film from the capillary film
2. wet the screen with water
3. place the capillary film with the side from which you removed the protective film onto the screen (the side of the screen that will be in contact with the print)
4. evenly pull the squeegee over both sides of the screen to remove excess water
5. dry the screen in a warm chamber (up to 40°C) in a horizontal position
6. the prepared screens can wait for several months in a dark place.

EXPOSURE TIMES

Important: These times are reference values for exposing a white mesh with a 5000 watt halogen lamp positioned 130 cm away from the table. They can aid in exposure but are dependent on many factors (mesh color, thread density, distance and intensity of light source, etc.).

Image: Comparison of a developed screen coated with liquid emulsion (left) and capillary film (right). Visible differences in edge sharpness and smooth surface.

You can order Polifast paint for polypropylene Grafco from us.

More information: barve@sitotisk.net or 01 54 22 300, Tamara

The Murakami capillary film MS is intended for creating excellent stencils with very simple coating techniques before preparing the screen.

An excellent substitute for liquid emulsion, which will allow you to develop fine details at the highest resolutions with ease.

Capillary film of 25 microns and 50 microns thickness in 30×40 cm sheets is in stock.

All other thicknesses (from 12 to 100 microns) and thick layer capillary films (thick film from 100 to 1000 microns) are available upon prior order. Available in two dimensions, either rolled on a 0.64×10 m roll or in 30×40 cm sheets.

PHYSICAL PROPERTIES:

› light blue colored capillary film

› thickness 12 – 100 microns

› for UV, solvent, and textile color systems

› exceptional resolution

› durable at high volumes

› easy coating process (with water or emulsion)

CAPILLARY FILM CAN BE APPLIED IN TWO WAYS:

APPLICATION METHOD WITH LIQUID EMULSION:
1. remove the protective film from the capillary film
2. place the film with the bare side up on a flat table
3. place the screen over the film so that the mesh touches the film
4. pour a little liquid emulsion on the screen above the film 1POT SOL C2 or Screencoat WHDevenly pull the squeegee twice over the film.
5. dry the screen in a warm chamber (up to 40°C) in a horizontal position
6. such prepared screens can wait for several months in a dark room.

APPLICATION METHOD WITH WATER:
1. remove the protective film from the capillary film
2. wet the screen with water
3. place the capillary film on the screen with the side from which you removed the protective film (the side of the screen that will be in contact with the print)
4. pull the squeegee evenly on both sides of the screen to remove excess water
5. dry the screen in a warm chamber (up to 40°C) in a horizontal position
6. such prepared screens can wait for several months in a dark room.

EXPOSURE TIMES

Important: These times are reference values for exposing white mesh with a 5000-watt halogen light placed 130 cm from the table. They can assist in exposure but depend on many factors (mesh color, thread density, distance and intensity of light source, etc.).

Image: Comparison of a developed screen coated with liquid emulsion (left) and capillary film (right). Visible obvious differences in edge sharpness and smooth surface.

The rubber is of extremely high quality, made of polyurethane through a special injection process. Polyurethane is an electrostatic and chemically resistant material with a long lifespan. Very suitable for use with all types of screen printing inks (solvent, water-based, plastisol, etc.).

Rubber dimensions: height 50 mm x thickness 9 mm

Red Squeegee Rubber of Hardness 65 SH

The red squeegee rubber is softer, with a hardness of 60/65°SH, suitable for high-quality screen printing of special effects. We recommend it for printing surfaces and uneven textures or printing special effects (glitter, puff, etc.).

Green Squeegee Rubber of Hardness 75 SH

The green squeegee rubber is medium-hard 70/75°SH, suitable for standard use in screen printing. We recommend it for printing halftone graphics and larger formats.

Blue Squeegee Rubber of Hardness 85 SH

The blue squeegee rubber is a harder rubber 80/85°SH, suitable for more demanding, halftone screen printing. We recommend it for standard printing up to HD (high definition) or more demanding screen printing on textiles.

Triple Green Squeegee Rubber of Hardness 75/90/75 SH

Triple green squeegee rubber with a medium-hard core layer of 90°SH and two outer medium-hard layers of 70/75°SH, suitable for standard screen printing applications. The white middle layer is harder at 90°SH, while the outer green layers are slightly softer, medium-hard at 70/75°SH. It is recommended for printing halftone graphics and larger formats or suitable for standard use in screen printing.

AVANTEX CLEAR BASE 3D FOR HIGH THICKNESS EFFECT KG.1

Transparent base for 3D printing layer effect, where the edges of the color after printing are clean and sharp. Suitable for use in combination with plastisol colors.

To achieve the right effect, the screen should be exposed with thick-layer emulsion or thicker capillary film (min. 400 mic.).

Recommended mesh density: 32 – 43 threads/cm

Additive for 3D base: R10 to achieve puff effect (use 10-15%).

IMPORTANT: Always test wash durability on a test print before serial printing.

AVANTEX LENS CLEAR, 1kg.

Plastisol clear base with a special varnish effect – PRINT WITH GLOSS.

Usage: Suitable for direct screen printing on textiles, for cotton and synthetic fibers. The product is printed on a dried color or multi-color print, as it is transparent.

The screen should be coated with a thick layer of emulsion or capillary film over 400 microns.

Composition: Plastisol ink based on PVC without phthalates.

Preparation for use: Mix the one-component paste well, simply take it out of the container, and print.

Always test the durability before printing large series.